Large walls and siege towers in 1.6...

[Mouzafphaerre]

.

and like it says in the thread title, 1.6.

The firing ability of siege towers can be disabled or their fire rates decreased but nothing can be done with wall towers and gatehouses, which are totally and anoyingly hardcoded.
.

[NihilisticCow]

I've just seen this happen as well in 1.6, where a unit of infantry kept moving backwards and forwards in front of the siege tower it was meant to be climbing, as if it was unable to get onto the tower slope bit at the bottom. Several minutes later, the units spontaneously all were able to get into the tower and climbed it. I tried using one of my units to climb the same tower and they had the same problem, so it's not just the AI.

[Cirith Ungol]

Hey MAt, Are you telling your soldires to climb the towers? ie clickin them and giving them a command to climb tower, because if so it could be that because in the new patch you dont have to command them to climb they just do it now. But I could be wrong since you say it happens to the A.I .
I havent had this problem , yet lol but one thing I have noticed is they did tweak the seige towers fire rate and it now doesnt have super arrows so it would seem anyway.

[Barbarossa82]

I can confirm that this happens. Last night I used a siege tower crewed by Eastern Infantry to attack a Large Stone Wall. They pushed it to the wall, then started milling about moronically at the bottom. After about 5 minutes of getting shot up, I tried to pull them back. They ignored my instruction and continued dancing around. Ordering them onto the top of the wall using the movement pointer also failed. Eventually I sent a second unit (btw normal unit scale) to join them. They also milled around for a few minuites, before one unit finally appeared at the top of the wall (don't know whether it was the original crew or the reinforcements.) This was approximately 12 minutes after the siege tower had reached the wall.

[MAt]

I can confirm that this happens. Last night I used a siege tower crewed by Eastern Infantry to attack a Large Stone Wall. They pushed it to the wall, then started milling about moronically at the bottom. After about 5 minutes of getting shot up, I tried to pull them back. They ignored my instruction and continued dancing around. Ordering them onto the top of the wall using the movement pointer also failed. Eventually I sent a second unit (btw normal unit scale) to join them. They also milled around for a few minuites, before one unit finally appeared at the top of the wall (don't know whether it was the original crew or the reinforcements.) This was approximately 12 minutes after the siege tower had reached the wall.

This is what I mean! afaik at the moment it only happens with most (but not all) siege towers going up against large roman walls... it just seems to be happening to me much more than anyone else for some reason...

[Kaldhore]

Ive noticed one thing VERY similar to this. May be the same thing - I dont know tbh.

I had a unit milling around the base of a seige tower refusing to climb inside. I had a good look around and notice 2 of the soldiers from that unit had been pushed magically through the wall at the base onto the city side base of the wall.

Hence the Unit of soldiers kept trying to reform, but where unble to do so because I hadnt bashed the gate in yet. Thus the 2 soldirs on the inside hadnt been able to magic themselves back through the wall into formation.

I had to leave that unit, but in another battle I saw it happening again so I blew the wall open and ordered the unit to run to the hole in the wall. Sure enough the magic soldiers were reunited with the formation - just for testing I then ordered them to climb the siege towere - which they did.

Houdini soldiers !

[Proletariat]

I was just about to post the same complaint, yet with sap points. This sucks.

[Red Harvest]

.



The firing ability of siege towers can be disabled or their fire rates decreased but nothing can be done with wall towers and gatehouses, which are totally and anoyingly hardcoded.
.

Actually, I think I know of a way to defang wall towers and gate houses. I'm not interested in doing it, but others might be. The structures make use of existing projectiles at least in descr_engines.txt, so most likely the same technique is used for the hardcoding...so if you move all units to copies of renamed projectiles in descr_projectile_new.txt, then cut the velocity down to a very low level on the default projectiles, cut out flaming options, eliminate body piercing etc. you can manually tune some of the projectile characteristics from these hardcoded points.

When I modified projectile speeds and eliminated fire arrows, I did it mostly by creating my own copies of each projectile, then assigning the projectiles to each unit. I did that to avoid weakening the defensive characteristics of walls/towers and engines.

Trick is: you have to know all the places each projectile is used so that you can update those that you want to leave the same by giving them the new copied name, while you tweak the original (that the wall/tower will be calling for.)

[Mouzafphaerre]

Actually, I think I know of a way to defang wall towers and gate houses. I'm not interested in doing it, but others might be. The structures make use of existing projectiles at least in descr_engines.txt, so most likely the same technique is used for the hardcoding...so if you move all units to copies of renamed projectiles in descr_projectile_new.txt, then cut the velocity down to a very low level on the default projectiles, cut out flaming options, eliminate body piercing etc. you can manually tune some of the projectile characteristics from these hardcoded points.

When I modified projectile speeds and eliminated fire arrows, I did it mostly by creating my own copies of each projectile, then assigning the projectiles to each unit. I did that to avoid weakening the defensive characteristics of walls/towers and engines.

Trick is: you have to know all the places each projectile is used so that you can update those that you want to leave the same by giving them the new copied name, while you tweak the original (that the wall/tower will be calling for.)

.
Sounds like intensive modding. Will try it in a mindfree state, thanks!

I see I have more and more reasons not to patch.
.

[Tyrac]

Done an awful lot of seiges with tons of towers and have never seen that happen. :) use 1.6